Select-increments Stealth-Pod Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Autolautsprecher Select-increments Stealth-Pod herunter. Select Increments Stealth-Pod User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 5
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
CAUTION:
1) Don’t let the banana plug prongs touch any metal when the pod is unhooked, you could damage your amplifier.
2) Never place objects on top of the pod, you may break the hangers.
3) Keep heavy, shifting cargo away from the pod; objects hitting the pod may break the hangers.
4) Make sure the subwoofer is screwed in with all eight screws and the foam gasket is between the woofer and the pod for an air-tight seal. If you’re
using your own subwoofer and it only has screw holes in the 12, 3, 6 and 9 o’clock positions, add 4 more screw holes between each of the
existing holes.
5) Screw the subwoofer screws in tightly, but don’t strip the plastic of the pod by screwing them in too tightly.
6) Hand-tighten the knobs to the tailgate carefully so as not to crack the plastic!
7) Make sure you plug in the pod correctly every time (i.e. pos+ to pos.+ and neg.- to neg.- You might want to mark it as such to avoid damaging your
amplifier and subwoofer.
8) Speaker Hole Cut-Out: From the factory, the hole must be made to accommodate subwoofers that require smaller mounting holes, so you may
have to cut the hole larger to accommodate a particular subwoofer. Easily done with a jig-saw or rotary cut-out tool, just use caution and take
your time.
Troubleshooting:
Rattling/Vibration – Make sure the subwoofer is screwed in tightly and that air is not escaping from the pod, causing the vibration. Sometimes when
conducting a sound check, the vibration you hear will not be detectable when driving the vehicle. CJ owners check to make sure all the metal snaps
for your soft-top are screwed in tightly. All models, check that all hardware attached to the tailgate is fastened tightly; all screws are tight and not
stripped, etc. Every vehicle is a little different and if something is vibrating, you may have to get creative: locate it and figure a way to isolate it. If
you are throwing enormous amounts of power to the subwoofer, the metal of the tailgate itself may rattle. There are two ways to fix this: 1) Less
Power. 2) Applying Dynamat® to the tailgate (the interior panel of the tailgate that the pod rests on).
Questions? Call us at 610-345-9044 or email us at a[email protected]
Select Increments is not responsible for any defects with amplifiers, speakers, or wiring kits. If you experience
any problems with these components, you must contact the manufacturer of these components for replacement
parts. Contact information and warranty cards are included with the audio components.
4 thick pan-head screws
hangers on pod
2 long pan-head
screws for handle
5 pan-head screw
for rubber bumper
And rubber feet
4 short flat-head
screws for terminal cup
8 pan-head screws
for knobs
(used later)
8 flat-head screws
for subwoofer
(used later)
Install hangers and bumper as shown
by using the tiny dimples in the pod
as starting points for the screws
Install handle as shown so that it lays flat, but can pull up like the photos.
Strip ends of wires and attach plug then crimp
female terminals on opposite end of wire.
Install terminal cup as shown.
Install rubber feet in
corners as shown
Tools: Measuring tape, drill, wire strippers/crimper, various sized phillips screwdrivers,
very small flat-head screwdriver, level, hammer, pick, pencil, masking tape.
1
Seitenansicht 0
1 2 3 4 5

Inhaltsverzeichnis

Seite 1

CAUTION:1) Don’t let the banana plug prongs touch any metal when the pod is unhooked, you could damage your amplifier.2) Never place objects on top

Seite 2 - FROM SELECT INCREMENTS:

1976-2002 CJ, YJ and TJ Wrangler:Your tailgate looks something like this:Some models have these, somesome don’t, they won’t interferewith your install

Seite 3

This particular photo represents ’76-’02 models and this close-up has three black squares representing the approximatepositions that the knob pieces f

Seite 4 - 2003-2006 TJ Wrangler:

2003-2006 TJ Wrangler:Your tailgate looks like this:The close-up photo below has three black squares representing the approximate positions that the k

Seite 5 - 2007 & Up JK Wrangler:

2007 & Up JK Wrangler:Your tailgate looks like this:Below: The close-up photo has three black squares representing the approximate positions that

Kommentare zu diesen Handbüchern

Keine Kommentare